Uncategorised

Week ending 3rd November

/ ,

Monday was a little quiet this week and not much in front of the camera.

Nevertheless LBH installed some plasticard floors in the short wheelbase S7 wagons

A few more attended on Tuesday; Fred working on a DJH kit for a D95xx BR(WR) 0-6-0 Diesel Hydraulic, Luke fettling the chassis of TR’s Dolgoch, LBH fettled the old wagons a bit and

Wagonman is making great progress with his ex-SR U class mogul from a David Andrews kit. Moving on from the tender, and having previously assembled the footplate and valences, he annealed the firebox and cab roof to make bending the complex curves easier. This shows the state of progress.

And Luke and LBH discussed plans for the Open Day and the development of the design for the S4 Jubilee Layout

By Friday the 4mm short wheelbase wagon had been primed, showing the detail more clearly. Not surprisingly the correct pattern buffer heads and rams are not readily available. An attempt was made with a standard buffer head and some 2mm brass tube. It needs gluing in properly. Cutting and fettling the short piece of brass required some time on the floor looking for the ones that escaped.

Week ending 3rd November Read More »

Week ending 27th October

/ , , ,

During the week we erected Frecclesham in the Layout Room to check that all was working satisfactorily prior to the Open Day. Thankfully it was.

At the start of the week work started on this and other 3D printed small wagons in 4mm. Below is one of the prototypes.

As 3D prints they arrive with support structure as below. They clean up pretty easily though carefull filing is needed to finish off. They are small, the material is light and adding extra weight for an empty wagon will be a bit of a problem

The hand rails on the ends do not always print well, so some 0.33 NS wire has been used.

Also on Friday Luke was putting together DG couplings for his shunting plank. The Dinorwic quarry wagons are some of the latest releases from Bachmann.

Not to be outdone, LBH is also building some short wheelbase Welsh wagons, this time in Scaleseven.

They are from the same source, Andrew Smith (eBay 3D printolutions) and are in development.

Week ending 27th October Read More »

Pavilion End at the Pavilion End

/ , ,

The Cardiff Model Show took place on the 19th and 20th October at Sophia Gardens Cricket Ground. We took the Chairman’s layout Pavilion End so that it could finally be at the . . . . . , well to be accurate in cricket terms, deep backward square leg.

Here’s the classic shot of the layout from the driver’s viewpoint. The coal train is departing now that the arriving train is in the platform. The pannier tank 5750 has propelled the District Inspector’s saloon up the branch and will now wait for a path back down to the main line.

At the back of the layout is the factory. Here the works shunter is delivering a new piece of equipment to the boiler house. A remarkably clean Iowerth Pritchard is having his morning tea and will leave the unloading to others inside.

Back at the platform the branch B-set has arrived.

Pannier 3603 has pushed the brake van right through the platform to get it behind the full coal wagons. The loco will next return to the front of the train and push it onto the brake van ready to carefully descend the valley.

Yes, the water crane is looking a bit droopy.

Finally a couple of shots of the cricket team itself. Late withdrawals have left just seven players, but it’s too late to cancel. Can they win with just seven? Yes, it can be done, ask Mr. Chairman. (Beware – a ball by ball account lasts 55 mins)

Pavilion End at the Pavilion End Read More »

Week ending 20th October

/ , ,

Monday was a quiet afternoon following the trip to Statfold Barn. To keep himself amused Mr. Chairman painted up some 4mm figures to go on ABB. One point noted at Scaleforum was that some locos did not have a crew on the footplate, or even a cab floor. Some of those in the picture are not true enginemen but in the cab of a tank engine are you going to notice?

Tuesday was better attended and Wagonman brought along the latest project – a SR U class mogul from a David Andrews kit. As you can see the tender went together well. This will be one of those engines that ran on the MSWJ line wandering south down to Andover and eventually Southampton.

Turning to narrow gauge, Luke has worked on a couple of purchases. The tiny diesel has had new pickups and after a bit of fettling and track cleaning began to run very well. The Talyllyn loco, Dolgoch, has been stripped ready for a repaint, though there is still work to do. Both of these are to 7mm scale running on 00 track.

Week ending 20th October Read More »

Orfe Quay and Tŷ’n-y-Coedcae at Warley at Statfold 

/ , ,

Two members’ layouts were at the Warley at Statfold show; Bernie’s Orfe Quay and LBH’s Tŷ’n-y-Coedcae

Orfe Quay

A general view of Orfe Quay

The Metro tank also ran on Hadley Town. 
Built by the late Vic Halliwell, it had run on the layout many years ago, soon after Paul Jones built it. 

Bernie would like to thank Alastair for all his help, together with Pete Rigby and Michael Sykes of EMGS for their help at the end.

Tŷ’n-y-Coedcae

Tŷ’n-y-Coedcae erected and ready for operation.

On loan from the Tanat Valley, GWR 2-4-0T No 1179 approaches Rhyd-y-Gwern halt with a short rake of B&MR four-wheel coaches.

A Victory class, a Minerva product, wheels reprofiled for Scaleseven but awaiting a repaint, eases a short freight through Tŷ’n-y-Coedcae in the Caerphilly direction. 
1197 again, this time with a close-coupled GWR set
Some TVR stock, painted by Dave Studley and borrowed from Wagonman

And some even stopped to look!

Thanks to the volunteer operators, Luke, Rob, Rhobat, Andrew J and Alastair. for operating and their compsany on a great weekend,

Fiji

As well as having show halls, Statfold also has the real thing. A special train for exhibitors was organised.

Orfe Quay and Tŷ’n-y-Coedcae at Warley at Statfold  Read More »

Week ending 13th October

/ , , , ,

Monday saw five of us at the club; Andrew J was working on Lyne Road, creating a bank at the back of the station area; Rhobat contemplating repainting the whitemetal GWR ex-Barry Class G 0-4-4T we saw back in w/e 15 September while Mr Chairman, Paul🏅🏅and LBH preparing Tŷ’n-y-Coedcae for its trip to Warley at Statfold on Friday. Switchblades were freed up and electromagnet switch cabling corrected. But nothing found its way to the camera.

Tuesday was busy with further preparation for Warley at Statfold. Which meant that Friday’s attendance was just a few of us with again little to report. But here are some pics from the show over the weekend.

Week ending 13th October Read More »

Members at Missenden

/ , , ,

Four of the club members attended the Missenden Abbey Railway Modellers’ weekend at Missenden Abbey, two of us working in 4mm/ft and two in Scaleseven.

After many tears years LBH is getting close with his S7 Brecon & Merthyr 0-6-2T

Keeping the South Wales pre-grouping theme, TVR class V kit was unwrapped and started. Here the valance is being soldered in place, the tiny clothes pegs are really useful here.

On the etch with the cab side you can see the lack of locating tabs and there are obviously then, no matching slots. By trial positioning, measuring and marking the cab was formed, turning out to be nice and square. Help from the tutor on our course was necessary for the bending of metal though.

Back in the 29 September post there is a picture of a 3D printed tank being inspected. In fact it fitted onto the brasswork pretty well, though some material had to be cut away from around the smokebox

4mm scale found an ADR railcar chassis with motor and radio control fitted, and the start of a kit for a Sharp Stewart 0-6-0. Can you spot the coupling rod that had been overheated by an RSU?

Members at Missenden Read More »

Week ending 6th October

/

Many shoulders to the wheel one Tŷ’n-y-Coedcae on Monday

Paul 🏅🏅made a removable shelf for the Tar Works siding on Tŷ’n-y-Coedcae. The split in the sleepers is a quick conversion from 0 gauge to S7!

Elsewhere Mr Chairman made up sprung inside-bearing units for S7 wheel sets for some wagons and Andrew J ground the old 0 gauge axles out, while LBH attended to some areas that were tight to gauge.

Conversion of this little beauty will have to wait for a few weeks though.

Tuesday’s Talk featured a presentation on Rhobat’s proposed layout. With the aim of keeping it simple and achievable it will be in 00 with a through mainline and a few sidings. It will be called Silstwn and is based on Gileston on the Barry Railway. Following on from that in a similar vein Andrew N ran us through his list of ‘Welsh stations that would make good models’. Then LBH had some additional pics gleaned from the internet.

Week ending 6th October Read More »

Week ending 29 September 2024

/ , , , , ,

Monday saw us getting things straight in the clubrooms, having quickly dumped ABB off after a long and fraught journey back from Scaleforum. LBH erected Tŷ’n-y-Coedcae in the vacant space in preparation for its trip to Warley at Statfold in a couple of weeks time.

Mr Chairman gave a casual glance to a 3d-printed smokebox/tank/fittings component for a TVR Class V from Taff Vale Models and pronounced himself very satisfied with the result.

Fred has done a great job finishing off LBH’s ADR No 14, here see posing at Rhyd-y-Gwern Halt.

LBH made a couple of additions to Tŷ’n-y-Coedcae in the form of a water crane (which still needs to be bedded in) and a storage tank in the Alma Tar Works.

Wagonman has completed a BR(WR) Autocoach in 0 Gauge.The trailer is a Hawkesworth A38 from an Orion kit – (now marketed by Ragstone) – finished in the lined crimson livery adopted from 1957- W223W was allocated to Gloucester in 1964 and was used on the final Gloucestershire Railway Society tour of the Cirencester and Tetbury branches before the railbus services ceased – also would have been a regular on the Chalford auto-service which finished in October 1964.

Here’s the same coach with its more modern partner. It is correct for the final service on the Chalford autotrains out of Gloucester. Loco 1472 was also at 85B at this time

Also from Wagonman is this composite coach from a Haywood Models kit. It will be used as the centre car of a three coach set suitable for secondary services.

Next on Wagonman’s list is a corridor connection – here we see it opening and closing.

Week ending 29 September 2024 Read More »

Scaleforum 2024

/ , ,

As has been trailed for a while we took ABB to Scaleforum this year.

En route we called in at the Didcot Railway Centre

We stopped for lunch.

Local Hero, Trojan, performed well

A Prairie sizzled

Trojan shuffled wagons and delighted us

The Castles looked OK

ABB got erected

The terrace fitted in well

The station operator’s view.

R&R after a long day

At the actual show we tend to be busy and forget to take pictures. Here’s one from later on Sunday.

No. 4 is collecting full coal wagons from the siding to take into the off-scene factory. Earlier in the sequence it had deposited empties in the same siding.

And of course, we can’t let an exhibition pass without the customary cold tea toast.

Here we see, L to R, Mr Chairman, LBH, Paul🏅🏅, TAFKATYS, Andrew N, Wagonman and Jonathan.

Scaleforum 2024 Read More »

Scroll to Top