Cwm Carno

Back to the club

The adventure to Ally Pally over we turned our attention back to Cwm Carno

TAFKATYS made a set of card mock-ups of the main colliery buildings to enable us to assess how they would fit into the layout topography and affect sight lines.

Meanwhile, back in the workroom, Luke has started on one of the points for Cwmcarno. The sleepers and timbers are cut to length and by the end of the session all were in place using double sided tape. Then there will be a bit of soldering to be done.

Continuing on Friday with the trackwork, more etched chairs were folded up by Mr C. After cutting off the fret they are folded with forceps, then finally shaped against the blocks with a screwdriver. Meanwhile Luke was soldering some into place.

For the control panel TAFKATYS tried out wiring and programming coloured LEDs to indicate the position of the points on the track diagram. This was successful so now the rest of the LEDs need wiring in.

Back to the club Read More »

Friday 7 March

Having bought some very cheap 7mm point work Mike E launched into a short line project titled the Hogwash and Balony Railroad. The station building is in progress and three very nice boxvan kits have arrived. They’ve probably cancelled out any savings made on the pointwork.

Away from the clubroom Andrew N has started to produce some track work for Cwm Carno – to be precise the colliery sidings and in flat-bottom to boot.

Friday 7 March Read More »

No pic Friday

Enough going on at the club this evening but nothing to precipitate the action of a camera shutter. There was a run through of the ABB timetable with a different combination of operators, TAFKATYS wired the control panel while Paul 🏅🏅 assembled the frame for the pelmet, both for Cwm Carno, the Wizard identified castings and LBH assembled a loom for the battery-power radio-control of ADR No 14.

Well, actually we did get one pic of how things were on Friday. This shows the progress TAFKATYS made on the Cwm Carno panel.

No pic Friday Read More »

Mainly Cwm Carno and some homework

After we fixed the trackbed on Cwm Carno it was apparent that it needed further support to prevent excessive flexing and ensure the it was in one plane throughout the areas supporting turnouts to give us the best chance of reliable running. Paul S added several braces to this end.

Sticking to Cwm Carno, Andrew N has produced what may prove to be the first items of stock specifically for the layout. They are all based on the Masokits whitemetal kits from the 1980s (when, coincidentally, LBH was involved in the enterprise).

And Wagonman looks like he has pretty well reached the finishing line with his ex-CMDPLR pannier.

Away from the clubrooms our members are busy:

Stephen B has created Locomotive no.7, aka “the brick”. It is being built for the mysteriously-titled Project Kevin and will be the test bed for battery powered radio control. He reckons that he should be able to get a small power station in there.

Mainly Cwm Carno and some homework Read More »

Preparations for Ally Pally etc.

With Abergavenny Blackbrook‘s visit to the London Festival of Railway Modelling at Alexandra Palace, London, which is now only three weeks away much of the evening’s efforts was in practicing operation on ABB.

Other works progressed though, with Luke turning his attentions from the body of his 0-4-0T to its chassis. A write-up of Luke’s build can be found in the Scaleseven Group website here.

Friday also saw TAFKATYS arrive with the planned control panel for Cwm Carno. After discussion the uncoupling magnet positions are settled and by Sunday it’s been completed.

Preparations for Ally Pally etc. Read More »

Cwm Carno trackbed and ABB uncouplers

Work continued on the trackbed on Cwm Carno, which is now fixed in place.

When we got the framework laser cut, thanks to TAFKATYS’s prescience, we also got a set of alignment gauges made to check the we had the correct elevation difference and that we hadn’t introduced a warp into the trackbed.

Elsewhere we worked on reviving and old Mainline pannier tank, uniting an elderly brass chassis with a modern Bachmann body. The chassis will need a bit of TLC and the body a bit of detailing and weathering but it should provide a useful loco for Cwm Carno.

Mr Chairman sorted out a problem that we had with one of the servo motors that move the uncoupling magnets on ABB. It was working in the wrong sense, that is normally in the up/uncoupling position, this was sorted out by swapping over the blue and orange cables inside the control box.

Cwm Carno trackbed and ABB uncouplers Read More »

Monday 17th February

Monday and the usual activities in the workroom, etched kits to the fore in Rhobat’s and the Wizard’s hands, while in the layout room work progressed on the Cwm Carno baseboard.

The river bed is the lowest, central strip of plywood.

We first gave attention the river bed, square wooden blocks screwed and glued to the vertical risers and the river bed for our version of Nant Carno.

Blocks have been fixed in place too for the trackbed, but it is seen here just placed in situ.

Forming the weir in Nant Carno.

Monday 17th February Read More »

Week ending 16th February

Monday saw five of us at at the club.

Continuing the etched brass tank engine meme from last week, Rhobat, with the helpful Wizard’s eye, is also essaying his first loco, in this case a Hunslet Jazzer kit in OO from the CSP range.

Meanwhile LBH converted a B&MR PBV to S7. Now it needs some serious weathering!

Tuesday evening we largely concentrated on runs-through of the ABB table honing a few items here and there. Wagonman continued to work on his ex-CM&DP pannier tank, the Wizard on a diesel (a Peak perhaps), and LBH on a gearbox for a 2-4-0T.

Friday and the next job to do on Cwm Carno was to cut the plywood for the track- and river beds. The initial idea was to extract the positions of the edges on the trackbed at 150 mm intervals from the drawing below.

That approach wasn’t welcomed by the club carpenter, Paul S!

Instead, we had already obtained a full-size print of the layout drawing for planning purposes, so we drilled small holes through it to plywood below marking the borders of the beds. Then by ‘joining up the dots’ we were able to use a jigsaw to the correct outline. Here we see the river bed in place, but not yet fixed.

And here’s the trackbed placed on the frame. The top of the picture is the top of the valley with, from the left, ‘mainline’, headshunt and colliery screens.

There are adjustments to make at the entry and exit points.

Meanwhile in the workroom a small parade of locos was assembled.; two pannier tanks and two 56xx’s. From left to right we have the Ditton Priors tank that’s featured before, two 4mm scale tanks from Mike E’s stable (which ran much better after the wheels had been thoroughly cleaned) and a brand new Minerva Models 7mm 56xx. This last belongs to Ed who in true Newport fashion has his feet in both the 4mm and 7mm camps.

Week ending 16th February Read More »

Week ending 9th February

Monday and our well-glued baseboard is set for ‘the test’. Will it fit into the intended vehicle? As long as it goes in low down for side clearance, it can be lifted up afterwards to allow items to be stored underneath. It is very light and we did notice that it will move in the wind.

Also Rhobat brought along the final prototypes for his Bryngaer Models Cambrian wagons. Looking very good.

And Rhobat completed the lineside hut for Cwm Carno.

First Tuesday of the month and we met on Zoom as usual. We looked at advance planning for which layouts need to be erected before they go on show, using Luke’s spreadsheet. Guided by LBH we visited a great variety of pubs from the Valleys seeking features to be included in the pub on Cwm Carno. (The Cordell Arms?) Then Mr Chairman talked about his visit to Bradenton MRC when on holiday in Florida over Christmas. SteveB continued down memory lane with pictures centred around the Cambrian mainline. (The Manors on the Cambrian Coast Express looked magnificent) Finally back to Luke for some Corris Railway and other narrow gauge pictures.

Friday. To help with planning the buildings and other scenery we had a full size printout of the drawn plan made. The proposed positions of the buildings will need a bit of revision, and better provisions made for gardens and the occasinal Tŷ Bach. Apologies for not the clearest photo.

Mr Chairman spent most of the evening trying to get the uncoupling sorted out for one particular movement on ABB. The horsebox and van in the picture have to be detached from the incoming train then deposited in the bay platform. After much swearing it was discovered that the long wheelbase of the green 3MT causes the couplings to swing wide on the curve into the bay and not release freely. The solution was to swop the loco for the shorter 84xx pannier tank.

and Wagonman making good progress with his ex-CMDP pannier tank, providing a lot of detail for the backhead.

Etched brass tank engine are continuing to absorb members efforts. Luke treading new ground with his S7 side tank.

Week ending 9th February Read More »

Week ending 2nd February

Monday saw us starting to glue together the baseboard for Cwm Carno,

By the end of the afternoon we had glued the perimeter, with a number of strengthening blocks added the joints. And we see Mr Chairman applying some PVA.

And Rhobat is making a hut for Cwm Carno, the roof is yet to finished.

Gluing and clamping continued on Tuesday along with discussion of materials for the trackbase and its fixing.

While all this was in progress we did our first practise timetable with ABB. There were the expected usual issues with coupling/uncoupling, otherwise it was satisfactory. The slightly revised timetable was better, though it would have helped if the signalman, yard and driver all had the same version.

Friday, and five of us chose to not watch Wales trying to play rugby. The Cwm Carno baseboard had dried nicely and was light and rigid enough for an ancient club member to lift by himself. It was on its way to being inverted, so that the last strengthening pieces could be glued underneath with assistance from Luke.

Meanwhile, back in the workroom;

Wagonman continues with the Ditton Priors pannier tank and brought along photos of it at Newport Dock Street in the 50’s.

Luke has the boiler test-fitted in place and the bunker completed.

The Welsh Wizard continued working on a pannier tank that needed TLC.

Week ending 2nd February Read More »

Scroll to Top